Electronic Remote Order Entry

Overview:

The Remote Order Entry process allows a third-party program to create an ASCII file for Rx-Universe, containing information necessary to order an Rx from the lab. This file uses the VCA convention for data transfers, with additional labels defined by Rx-Universe for fields not directly supported by the VCA device standard. These additional labels will have a suffix of an underscore “_”; for example “_FIRSTNAME”.

Rx-Universe can also create a status file which the third-party software can retrieve to obtain the status of each of the site’s job in the lab. The lab would need the Rx-Tracker module installed to accomplish this task. Figure I-1 shows this process.

This document will explain what codes you need to send to Rx-Universe, the format in which the request/orders will need to be sent to Rx-Universe and how to interpret the information that Rx-Universe sends back.

Figure 1-1

Rx-Universe Inbox (for incoming orders into the lab)

Information (RAW files) coming from the retail site will be stored in a folder determined by the lab which is located on the lab’s server. The most common method of file transfer from a retail site to the lab is via ftp, where the default folder for the ftp transfer will point to the appropriate folder. By default the folder is “OMICSTX” a subfolder of the “RXUNIVERSE” folder on the lab’s server. For example “C:\RXUNIVERSE\OMICSTX”.

Rx-Universe Outbox (for outgoing status results)

Information that is sent back from Rx-Universe will be located in this directory, which is usually called “OMICSRX” – this is usually a subfolder below the default “RXUNIVERSE” folder on the lab’s server. For example “C:\RXUNIVERSE\OMICSRX”. Under this folder there is a folder for each customer created by Rx-Universe automatically, the folder name will be the account number, this is where the retail site will have to pick up the status files.

For example “C:\RXUNIVERSE\OMICSRX\account_number”:
- “C:\RXUNIVERSE\OMICSRX\1” (status files for account 1)
- “C:\RXUNIVERSE\OMICSRX\0025” (status files for account 0025)
- “C:\RXUNIVERSE\OMICSRX\1234” (status files for account 1234)

Naming Conventions

There are naming conventions that are used for every document Rx-Universe either sends or receives and the directories they are stored in. Each of these naming conventions will be explained as we get into detail about each document.

Sending Orders To Rx-Universe

File Name:

The naming convention that is used for the order file is very important. The retailer will need to get their account number from the lab and store it somewhere in their system, since it is used in the flat file (RAW File) name.
The format of the file name is Account Number.V + sequence number (2 to 4 digits)

Example:

If the account number is “002” and this is the first order that they are sending, the text file name would be “002.V01” or “002.V0001”
The second file would be “002.V02” or “002.V0002” ... and so on. Once the sequence number reaches its upper limit, the sequence number should restart from the beginning; for example, after “002.V9999” it should be “002.V0001”.

Steps in sending an Order to the lab:
Generate ASCII text file (RAW File) for every order that has not been sent.
Send the ASCII text file(s) (RAW File) to the lab.

File Format
Each line in the ASCII file must have at least two parameters, the first parameter being the field name (label), the second parameter the field value. These parameters must be separated by an equal sign “=”. Each field must go on a different line. Field names with no underscore “_” at the beginning of its name are VCA Labels. For more detail information on VCA Labels, reference the VCA Data Communication Standard documentation.

Some fields you have to send a right value and a left value, separated by a semi-colon. These fields are indicated by the "chiral" column. Here is an example:

FIELDNAME=RightData;LeftData
SPH=-1.25;-0.75

If you are only sending Left eye information, you still have to include the semi-colon before the field value:

FIELDNAME=;LeftData
SPH=;-0.75

A complete order file will consists of many fields, with corresponding values. A list of fields is given; following the list is an example of a complete order submission.

General Information

Required column - O=optional, R=required
Chiral column - N=non-chiral (one value per label); Y=chiral (value is right, semi-colon, left - ie 2.50;1.25)

Field Name	Reqd	Chiral	Data Type	Length	Description	Format / Valid Values
_CUSTNO	O	N	String	09	Account Number
JOB	R	N	String	21	Job number from retail	This information is saved in the “PO#” field.
_INV or ORDER-NUM	O	N	String	08	Invoice number	Use this field if you want to keep the same Invoice Number as the sending/original system.
_OMICS_TRAY_NUM	O	N	String	06	Tray Number	Use this field if you want to keep the same Tray Number as the sending/original system.
_JTYPE	R	N	String	01	Job Type	Valid Values: “1” – Full Job “2” – Uncut Job
PATIENT	R	N	String	21	Patient Name	This field is not needed if you are using the “_FIRSTNAME” and “_LASTNAME” labels.
_FIRSTNAME	R	N	String	21	First name of patient	Use either PATIENT or combination of first and last name
_LASTNAME	R	N	String	21	Last name of patient	Use either PATIENT or combination of first and last name
_RDATE	O	N	String	08	Date Ordered	YYYYMMDD
_WDATE	O	N	String	08	Date Wanted	YYYYMMDD
_OPT_WDATE	O	N	String	8	Optional date wanted	YYYYMMDD
REF or _REF	O	N	String	18	Release Number
SHIPTO	O	N	String String String String String String	10 35 25 25 20 24	Ship to Number Ship to Name Address Line 1 Address Line 2 Address Line 3 Address Line 4	Each part separated by a comma.
REM or _COMMENT	O	N	String	30	Remarks or Special Instructions.	Can have up to 11 comment lines.
_CALLFST	O	N	String	01	Call first before processing. Set to Y will cause Rx-Universe to save the job unvalid and on hold. (ie. call dispenser before processing).	Valid Entries are: “Y” – Yes "N” or blank – No
_REMAKECODE	O	N	String	04	Remake code	An entry in this field sets the REDO flag on the order and sets the job as Unvalid
_RUSH_JOB	O	N	String	01	Set Rush indicator on order	Valid Entries are: “Y” – Yes “N” or blank – No
_DOCTOR_ID	O	N	String	30	Doctor’s name
_ORD-ORIG_INVOICE	O	N	String	08	Used to send the original invoice number when sending a remake job
_REMAKE_CAT	O	N	String	04	Used to send the remake category
_PRLIST	O	N	String	03	Price list number.	Specify to force pricing to a certain lab price list.
_TRAY_COLOR	O	N	String	03	Used to override the tray color that would normally be associated with the order.
_LAYOUT	O	N	String	01	Indicates whether frame measurements should be considered exact, approximate, or not present.	Valid Entries are: “A” – Approximate (do not use for finish layout calculation) "E” – Exact measurements. “U” – Uncut job, no frame measurements present, just uncut diameter.
_UNCUTDIAM	O	Y	Numeric	05	Diameter to use for thickness for uncut job (with no frame measurements)	Value >= 0 and <= 99.9 Ex: _UNCUTDIAM=65;67
_USER_DEF_JF	C	N	String	10	User Define Job Flow Labels. Job Tracking module is required.

Rx And Lens Information

Field Name	Reqd	Chiral	Data Type	Length	Description	Format / Valid Values
DO or _EYE	R	Y	String	01	Which eye	Valid Values: “R” = Right “L” = Left “B” = Both
_LSTYLE See Appendix 2	C	Y	String	06	If _LCODE not specified, this field specifies the lab code for the lens style being ordered
_MATERIAL See Appendix 2	C	Y	String	02	If _LCODE not specified, this field specifies the lab code for the lens material being ordered
_TREAT See Appendix 2	C	Y	String	03	If _LCODE not specified, this field specifies the lab code for the treatment of the lens being ordered (if any)	This is the Pretreatment that comes already on the lens from the manufacturer.
_TINT See Appendix 2	C	Y	String	03	If _LCODE not specified, this field specifies the lab code for the tint of the lens being ordered (if any)	This is the Tint (Color) that comes already on the lens from the manufacturer
_LCODE See Appendix 1	C	Y	String String String String	02 06 03 03	Lens Material Lens Style Lens Treatment Lens Tint Required if you are ordering lenses.	Refer to catalogue reference, under the lens section. This is the code from the catalogue which specifies the lens product to order. NOTE: you may use _LSTYLE, _MATERIAL, _TINT and _TREAT in lieu of the _LCODE In our experience, it is easier to use the other labels than using _LCODE.
SPH +/-	R	Y	Numeric	05	Rx Sphere Power	Range from -39.0 to +49.0 and must be a multiple of 0.125, rounded to 2 decimal places (ie. 0.12, 0.25, 0.37, etc.), unless the lab supports powers in 1/100 D
CYL +/-	O	Y	Numeric	05	Rx Cylinder Power	Valid values range from-19.75 to +19.75, in increments of 0.125, rounded to the nearest 2 decimal places, unless the lab supports powers in 1/100 D
AX	C	Y	Integer	03	Prescribed Cylinder Axis. This field is required if the “CYL” field is specified for the eye.	Valid values range from 0 to 180.
IPD	R	Y	Numeric	03	Far PD: The far interpupillary distance for Multifocals and can be entered as monocular or binocular PD. or This can also be the Horizontal Decentration.	Valid range values: For monocular: 17mm to 38mm. For Ex: IPD=30.0;30.5 For binocular: 39mm and over. For Ex: IPD=60.0;61.0 16 or less indicates decentration. This value may be negative, indicating “out” decentration.
NPD	C	Y	Numeric	03	Near PD or Vertical Decentration: This is the near interpupillary distance for Multifocals and can be entered as monocular or binocular PD. or This can also be the Vertical Decentration for Single Vision lenses.	Valid range values: For monocular: 17mm to 38mm. For Ex: IPD=30.0;30.5 For binocular: 39mm and over. For Ex: IPD=60.0;61.0 For SV-Style lenses, this field represents the distance above or below the datum of the OC. If the value is positive, it’s above the datum and if the value is negative, it’s below the datum.
OCHT	O	Y	Numeric	04	Vertical O.C. height measured from the lower boxes tangent of the frame.
ADD	C	Y	Numeric	04	The add power of the multifocal segment; required for multifocal lenses	99.99
ADD2	C	Y	Numeric	04	The add power of the upper segment in an occupational lens	99.99
SEGHT or SGHT	C	Y	Numeric	03	Segment Height Required for multifocal lenses – this is the height of the segment from the bottom of the frame. Valid range of values is from +10.0mm to +40.0mm, in increments of 0.5mm.	Ex: SEGHT=19;19
PRVM +/-	O	Y	Numeric	04	Rx Prism in diopters Can specify up to 2 Rx Prisms per eye.	Ex: PRVM=1.50;3.00 PRVM=0.50;0.75
PRVA	C	Y	String	03	Rx Prism direction Required if PRVM has been populated Prism direction is the axis of the prism base, from 1 to 360 degrees You are allowed to specify as many PRVAs as PRVMs	Ex: PRVA=090;090 PRVA=000;180
ELLH	O	Y	Numeric	02	Elliptical Cribbing	Ex: ELLH=62;62
_SUPELLH	O	Y	String	01	Suppress Elliptical Cribbing Suppress means do not do Elliptical Cribbing	Valid Values are: “Y” – Do suppress "N” or blank – Do not suppress
THNP	O	Y	Numeric	03	Requested edge thickness at the thinnest edge If job has frame measurements, this is the thickness at the thinnest edge point on the frame. If uncut without frame, this is the thickness at the thinnest edge point on the crib shape.	Ex: THNP=1.5;1.5
_PRTHIN	O	N	String	01	Prism Thinning If you activate this option, OMICS will use the Prism Thinning value assigned to this account.	Valid Entries Are: “Y” – Yes, perform Prism Thinning “N” – No, Do Not, perform Prism Thinning
_ADDON	O	N	String	06	Add-on Codes Can have up to 15 add-ons	Codes specified by receiving lab or from catalogue.
CLASS	O	Y	String String	03 03	To force Finished (Stock) or Semi-Finish lenses per eye CLASS=FIN;SFN	Valid Values “FIN” = Finished Job “SFN” = Semi-Finished Job This works the same way as _FORCESF_F
_FORCESF_F	O	Y	String	01	To force Semi-Finish or Finished (Stock) lenses on your job	Valid Values: “2” = force finished lenses “3” = force semi-fin lenses This works the same way as “CLASS”.
_RFRONT or MBASE	O	Y	String	04	Requested Nominal Front Curve	Ex: _RFRONT=0400;0400 or MBASE=0400;0400
_RDIA	O	Y	Numeric	02	Requested Blank (Lens) Diameter	Ex: _RDIA=76;76
_LMFRID or LMFR	O	Y	String	04	Lens Manufacturer	If you want to force Rx-Universe to select a lens from a certain manufacturer
OPC	O	Y	Numeric	10	Lens OPC Code	Select lenses by OPC codes
SWIDTH	C	Y	Numeric	02	Segment Width Required only for certain Bifocal lenses. This is not needed when the Lens Style selected already specify the Segment Width.	Ex:_SWIDTH=28;28
SDEPTH	C	Y	Numeric	02	Segment Depth of the Intermediate Segment. Required only for Trifocal lenses This is not needed when the Lens Style selected already specify the Segment Depth	Ex:SDEPTH=08;08
LNAM	O	Y	String	23	VCA Label Translation
LTYP	O	Y	String	23	VCA Label Translation
LMATTYPE	O	Y	String	23	VCA Label Translation
HBOX	C	O	Numeric	03	Horizontal box lens size of the frame. This is the “A” measurement This field is required if there is no pattern sent	Valid range of values is from 30.0 to 80.0 mm
VBOX	C	O	Numeric	03	Vertical boxes lens size of the frame. This is the “B” measurement. This field is required if there is no pattern sent or if the HBOX measurement exists.	Valid range of values is from 15.0 to 60.0 mm
_EDBOX	C	O	Numeric	03	“ED” measurement of the box measurement system. The widest possible diameter of the Frame This field is required if there was no pattern sent and the brow, cheek, and temple are not supplied.	Valid range of values is from 30.0 to 80.0 mm
DBL	R	N	Numeric	03	Distance Between Lenses	Valid range of values is from 7.0 to 30.0 mm
ETYP	O	N	String	01	Type of edge to cut on lens.	Valid Entries are: 1 – Bevel 2 – Rimless (drilllmount) 3 – Groove
SFTHK	O	N	String	01	This field needs to be placed after the “ETYP” field	Y = Safety Thickness
FTYP	O	N	String	01	Frame Type	Valid Entries are: 1 – Zyl (Z) 2 – Metal (M) 3 – Rimless
_TRACE See Appendix 3	O	N	String	12	Trace Number	Rx-Universe will look into the Pattern Database for a Frame Name matching the value of “_TRACE”, with the Manufacturer of “DATA”, the Nominal A Size field being blank and the Nominal Bridge field being blank.
_CCIRC or CIRC	O	N	Numeric	04	You can specify the actual circumference of the customer’s frame. This will only work if a trace has been attached to the job by sending the frame trace data or by selecting a pattern or frame with tracing information from the Rx-Universe Tracing Database. For example, with the use of _TRACE label.	Ex: CIRC=138.4
_WRAP	O	N	String	01	To take advantage of the Wrap Frame Calculation. Required: FrameWorks V2.0 (or higher) to be installed on the processing computer. If the processing computer is connected to the server through thin client, then it has to be installed on the server.	Valid Entries are: “Y” – Yes “N” or blank – No
ZTILT	O	N	Numeric	03	Panoramic (Wrap) Angle Required: _WRAP to be valid	Valid range of values is from 0 to 30.0 degrees
PANTO	O	N	Numeric	03	Pantoscopic (Angle) Tilt Required: _WRAP to be valid.	Valid range of values is from 0 to 30.0 degrees
BVD or _VERT_FITTING	O	N	Numeric	03	Vertex Fitting. Back vertex distance, as worn (mm) Required: _WRAP to be valid	Valid range of values is from 5 to 30 mm
RVD	O	N	Numeric	03	Refracted Vertex Distance - Back vertex distance, as refracted (mm) Required: _WRAP to be valid	Valid range of values is from 5 to 30 mm
TRCFMT	O	N	Numeric	01	Format of frame trace data For more detail information, reference the VCA Data Communication Standard documentation.	Valid Entries are: 0 – No Trace sent. 1, 3, 4 – supported by Rx-Universe and specified in VCA standard 2 – NOT supported by Rx-Universe 5..100 – are reserved for future standards.
			Number	04	Number of radii in the trace
			String	01	Radius mode identifier	Valid Entries are: “E” – the radii are evenly spaced “U” – the radii are unevenly spaced
			String	01	Which eyes are included	Valid Entries are: “R” – Right “L” – Left “B” – Both
ZFMT	O	N	Numeric	01	Format of vertical height frame trace data For more detail information, reference the VCA Data Communication Standard documentation.	Valid Entries are: 0 – No Trace sent 1, 3, 4 – supported by Rx-Universe and specified in VCA standard 2 – NOT supported by Rx-Universe 5..100 – are reserved for future standards
			Number	04	Number of radii in the trace
			String	01	Radius mode identifier	E – the radii are evenly spaced U – the radii are unevenly spaced
			String	01	Which eyes are included	R – Right L – Left B – Both
R	C	N	Numeric	05	Radius Data For more detail information, reference the VCA Data Communication Standard documentation.	Separate values for this field by a semi-colon “;” such as: R=2479;2583;2605;2527;… All of the records follow the 80-character line limit rule; therefore there may (in fact, will likely) be multiple R records for each tracing. Radius is expressed in hundredths of a degree with an implied decimal point.
A	C	N	Numeric	05	Angle data for radius data (angular locations of trace radii expressed in R record(s)) For more detail information, reference the VCA Data Communication Standard documentation.	Separate values for this field by a semi-colon “;” such as: A=010;015;020;025;…
Z	C	N	Numeric	05	Radius Data For more detail information, reference the VCA Data Communication Standard documentation.	Separate values for this field by a semi-colon “;” such as: Z=179;183;205;227;… All of the records follow the 80-character line limit rule; therefore there may (in fact, will likely) be multiple Z records for each tracing. Height is expressed in hundredths of a degree with an implied decimal point.
CTHICK	O	Y	Numeric	05	Center thickness - used only if a specific center thickness is desired for the lens. This can be specified for both minus power and plus power lenses.	CTHICK=2.3;2.3

Optional Fields

Optional fields are parameters that are not required for all Rx's, but might be required for specific lens designs. For example, the Varilux S 4D lens style requires head-eye coefficient to be specified by the dispenser.

If sent, the values will be used if applicable for the lens design ordered.

Field Name	Chiral	Data Type	Length	Description	Format / Valid Values
CLINIT	N	String		Wearer’s Initials	up to 4 alphanumeric characters
CLHT	N	Numeric		Client Height in meters
HEADK	N	Numeric		Head Eye Coefficient	Measured by Visi-Office Values 0 to 0.99
HEADS	N	Numeric		Stability Coefficient	Measured by Visi-Office Valid values 0 to 0.15
_NVI	Y	Numeric		Near Vision Inset	Inset of the near vision segment relative to the distance reference point Valid values are 0 to 7.0 mm
NWD	N	Numeric		Near Working Distance	Working object distance at near viewing point (in meters).
ERCD	Y	Numeric		Eye Rotation Center Distance	Measured by Visi-Office Values 16.0 to 38.0 mm
CAPE	Y	Numeric		Cape Head Angle	Measured by Visi-Office Values -10 to +10
_LP	Y			Progression Length (corridor length)	Valid values vary by design Typically 13, 14, 15, etc., in 1/10 increments
DMNTEYE	N			Dominant Eye	R-right, L-left, or N-none
_CLLAT or CLHLAT	N			Laterality (Dominant Hand)	Valid Entries are: “R” – Right “L” – Left "N" - none
NOD	Y	Numeric		Refracted object distance at near viewing point (meters)	Valid values 0.20 to 0.60 m
CLNVB	N	String	7	Near Vision Behaviour, used for Essilor Varilux X designs	Must be 7 alphanumeric characters; for example CLNVB=HCN7DEV

This ASCII text file will be generated at the retail site and be sent to the lab from which they are placing their order. The following is an example of items you can find in an order file (RAW file):

PATIENT="JOHNNY WISHBONE"
_RDATE=20150120
_WDATE=20150125JOB="7430004"
_INV="7430004"
REM="PLEASE SHIP UPS"
DO=B
_JTYPE=1
_LSTYLE=SV;SV
_MATERIAL=P;P
SPH=+01.00;+02.25
CYL=-01.00;-01.00
AX=88;159
IPD=30.0;29.0
HBOX=62.5
VBOX=39.4
DBL=16.0
FTYP=2
ETYP=1
TRCFMT=1;400;E;R;F
R=2559;2567;2575;2584;2593;2601;2611;2620;2628;2638;2646;2655;2664;2672;2681
R=2690;2699;2707;2715;2723;2730;2736;2743;2747;2751;2753;2755;2756;2755;2755
R=2754;2753;2750;2746;2741;2737;2732;2726;2718;2711;2703;2694;2685;2675;2666
R=2656;2645;2634;2623;2611;2599;2587;2575;2563;2552;2539;2527;2514;2502;2490
R=2479;2468;2455;2443;2431;2419;2408;2396;2386;2375;2365;2355;2345;2336;2329
R=2321;2312;2304;2297;2292;2285;2279;2274;2269;2264;2260;2257;2253;2250;2247
R=2245;2243;2242;2241;2240;2240;2239;2239;2239;2241;2243;2245;2248;2251;2255
R=2258;2263;2268;2273;2278;2284;2290;2296;2303;2311;2318;2326;2334;2343;2353
R=2363;2374;2384;2395;2405;2417;2429;2441;2454;2468;2480;2493;2506;2516;2526
R=2547;2556;2571;2585;2598;2611;2625;2637;2650;2662;2671;2684;2693;2703;2711
R=2720;2726;2732;2735;2739;2741;2745;2746;2749;2750;2750;2750;2750;2749;2746
R=2743;2739;2734;2729;2723;2719;2712;2706;2701;2697;2692;2688;2682;2676;2671
R=2666;2660;2656;2652;2648;2644;2642;2639;2637;2635;2633;2630;2628;2626;2624
R=2622;2620;2619;2618;2617;2617;2617;2617;2618;2618;2619;2621;2622;2625;2627
R=2629;2632;2636;2639;2643;2646;2650;2654;2658;2661;2665;2668;2672;2675;2678
R=2680;2682;2683;2684;2686;2690;2693;2696;2698;2700;2701;2701;2701;2702;2702
R=2700;2697;2694;2690;2686;2682;2677;2671;2666;2659;2652;2644;2635;2625;2615
R=2605;2595;2583;2572;2561;2549;2539;2528;2516;2503;2491;2481;2471;2458;2447
R=2436;2425;2414;2405;2395;2386;2378;2370;2362;2355;2347;2340;2331;2324;2317
R=2310;2303;2298;2293;2288;2283;2278;2274;2269;2265;2262;2260;2257;2254;2251
R=2248;2245;2243;2242;2240;2239;2238;2238;2237;2237;2237;2237;2237;2237;2237
R=2237;2237;2238;2238;2239;2239;2240;2242;2243;2244;2246;2249;2251;2253;2255
R=2258;2260;2263;2265;2268;2271;2273;2276;2278;2281;2283;2284;2286;2288;2291
R=2292;2295;2296;2299;2300;2302;2304;2305;2307;2310;2312;2313;2315;2317;2319
R=2321;2324;2325;2328;2331;2335;2337;2340;2343;2347;2350;2355;2359;2363;2370
R=2375;2379;2385;2391;2397;2403;2409;2414;2421;2429;2435;2443;2449;2457;2464
R=2472;2481;2489;2498;2506;2516;2525;2533;2542;2550
TRCFMT=1;400;E;L;F

R=2547;2547;2548;2548;2549;2550;2550;2551;2552;2553;2553;2554;2556;2557;2557
R=2559;2560;2561;2562;2564;2565;2566;2567;2569;2570;2572;2574;2576;2578;2580
R=2582;2584;2586;2588;2590;2591;2593;2595;2597;2599;2602;2604;2606;2608;2610
R=2612;2614;2616;2618;2619;2620;2623;2625;2628;2631;2634;2637;2639;2637;2630
R=2619;2605;2590;2575;2558;2543;2530;2517;2503;2489;2475;2462;2447;2435;2424
R=2410;2399;2386;2375;2363;2352;2342;2333;2323;2314;2307;2299;2291;2284;2277
R=2272;2266;2261;2255;2250;2246;2242;2239;2236;2233;2233;2230;2229;2229;2229
R=2229;2229;2231;2232;2234;2236;2238;2242;2246;2249;2254;2259;2264;2269;2274
R=2280;2286;2292;2299;2307;2315;2323;2332;2342;2351;2361;2369;2379;2388;2398
R=2408;2417;2428;2439;2450;2460;2471;2482;2493;2505;2516;2527;2538;2549;2560
R=2570;2580;2591;2601;2610;2619;2627;2636;2644;2651;2658;2665;2672;2679;2684
R=2689;2692;2695;2697;2697;2698;2697;2696;2695;2692;2689;2685;2680;2674;2668
R=2660;2653;2643;2635;2627;2618;2610;2601;2593;2584;2575;2566;2557;2546;2537
R=2528;2518;2509;2499;2490;2480;2471;2462;2452;2444;2435;2426;2417;2409;2400
R=2392;2384;2377;2370;2363;2357;2351;2345;2340;2336;2331;2326;2322;2316;2312
R=2306;2302;2297;2293;2290;2286;2283;2280;2277;2274;2272;2268;2266;2263;2261
R=2258;2256;2253;2250;2248;2246;2243;2242;2240;2237;2236;2233;2232;2230;2227
R=2226;2224;2222;2221;2219;2217;2215;2215;2214;2212;2212;2210;2208;2207;2205
R=2205;2203;2201;2200;2198;2196;2194;2194;2192;2191;2191;2190;2191;2190;2191
R=2191;2191;2193;2194;2195;2197;2198;2198;2202;2204;2208;2209;2213;2215;2218
R=2222;2226;2230;2235;2239;2244;2249;2254;2260;2266;2272;2277;2284;2291;2298
R=2306;2314;2323;2332;2340;2348;2357;2368;2377;2387;2394;2405;2414;2424;2434
R=2444;2456;2468;2477;2490;2501;2511;2525;2536;2548;2559;2569;2580;2593;2603
R=2614;2617;2615;2611;2607;2604;2602;2599;2597;2594;2592;2590;2588;2586;2584
R=2581;2579;2578;2576;2574;2572;2570;2568;2566;2564;2562;2561;2560;2558;2557
R=2556;2555;2554;2553;2552;2551;2550;2549;2548;2548;2547;2547;2547;2546;2546
R=2546;2545;2545;2546;2545;2545;2546;2546;2546;2547
EOJ=END OF JOB

Sending Status Requests / Other

(See Appendix 4)

You can make requests from the lab through Rx-Universe; the types of requests that you can make are as follows:
       Request quote (Rx-Invoice and Rx-Connect Modules Required at the Lab)
       Request order status (Rx-Tracker and Rx-Connect Modules Required at the Lab)
       Request to cancel the order
       Request to hold the order
       Request to ship the order

To do this, you basically have to send the ASCII order file again, with only these fields:

JOB=12345
_ACTION=3

Field Name	Data Type	Length	Description	Format / Valid Values
JOB	String	07	The original Job or PO number of the job that you are inquiring about.
_ACTION	Numeric	01	The type of request you are making.	Valid Entries are: 2 – Request a Quote (Rx-Pricing Required) 3 – Request Order Status (Rx-Tracker Required) 4 – Request to Cancel 6 – Request to Hold 7 – Request to Ship (Rx-Tracker Required)

Receiving Order Status

(See Appendix 4)

Order Status are received after an order is sent or the user can specifically make an order request. The retail system will have to pick the order status up from the lab. After an order is processed it creates a file in a folder that is specified in the Rx-Universe Remote Order Processing Options screen + “\” + Retail Account Number. The file name will consist of the “Job Number”.STA

Example:

Account 1234 sends an order with a job number of 35. In the Rx-Universe Remote Order Processing Options screen, the “Directory For Status Status File” is set to C:\RXUNIVERSE\OMICSRX”.

The file would be:

“C:\RXUNIVERSE\OMICSRX\1234\35.STA

The text file that would be sent would look like this:

ACCN="1234"
JOB="35"
_STATUS=7
_LABSTAT="In lab"
_ESTCOMP=20090929
_ESTCOST= 137.89
_INVNO=356186

Field Name	Data Type	Length	Description	Format / Valid Values
_LABID	String	12	The lab number
ACCN	String	08	The retailer’s account number with the lab
JOB	String	21	Job or PO number
_STATUS	Numeric	02	Order Status Code	Valid Entries are: 5 – Cancel, order rejected, request denied (if cancel request sent) 6 – Order quoted 7 – Order in progress (more detail in description) 8 – Order completed 10 – Order Cancelled (if cancel request sent)
_LABSTAT	String	60	Order Status Description	(see above field)
_LABREM	String	30	Lab Remarks	Can occur multiple times
_ESTCOMP	Date	08	Estimated Completion Date	YYYYMMDD
_ESTCOST	Numeric	10	Estimated Cost	99999999.99
_INVNO	Numeric	08	Invoice Number	99999999

Appendix 1:

_LCODE:

RAW File:

DO=B
_LCODE=C IMAGE TR7BN3;C IMAGE TR7BN3

O/E Rx Screen:

Appendix 2:

_LSTYLE, _MATERIAL, _TINT and _TREAT:

RAW File:

DO=B
_LSTYLE=IMAGE;IMAGE
_MATERIAL=C;C
_TREAT=TR7;TR7
_TINT=BN3;BN3

O/E Rx Screen:

Appendix 3:

_TRACE:

RAW File:

_TRACE=FRAME-1

O/E Rx Screen:

In the Frame Traces:

Appendix 4 - Sending and Receiving Order Status:

Lab’s Rx-Universe requirements:

- Rx-Universe Basic.
- Rx-Connect.
- Rx-Track.

File 1.V0054: This is an example of a job order file that the 3^rd party software would send to the “\RXUNIVERSE\OMICSTX” folder on the lab’s server.

PATIENT="JONIE BOBBY-PIN"

_RDATE=20151118

_WDATE=20151120

DO=B

JOB="20001"

_JTYPE=1

SPH=2.50;2.25

CYL=-3.75;-4.00

AX=55;114

_LSTYLE=SV;SV

_MATERIAL=P;P

IPD=34;34

DBL=19

HBOX=52

VBOX=35

_EDBOX=55

EOJ=END OF JOB

File 1.V0055: This is an example of a Status Request file that the 3^rd party software would send to the “\RXUNIVERSE\OMICSTX” folder on the lab’s server. You need to send one Status Request file for each individual order you want status information. Once in the “OMICSTX” folder, the Remote Processor (Rx-Connect) will process the file (request). More information in the “Sending Status Requests / Other” section.

JOB="20001"

_ACTION=3

File 20001.STA: This is an example of a Status Result file that will be created in the “\RXUNIVERSE\OMICSRX\account_number” folder after Rx-Universe Remote Processor (Rx-Connect) processes the “1.V0055” Status Request file.

- For example: “C:\RXUNIVERSE\OMICSRX\1\”.
- This folder is setup in the “Remote Order Processing Options:

- Then the 3^rd party software (system) would have to retrieve this file and import it into their system. More information in the “Receiving Order Status” section.

File 20001.STA:

ACCN="1 "

JOB="20001 "

_STATUS=7

_LABSTAT="VFT ORBIT "

_ESTCOMP=20151120

_ESTCOST= 330.00

_INVNO=206128