Anchor | ||||
---|---|---|---|---|
|
Search Optifacts User Documentation
Live Search | ||||
---|---|---|---|---|
|
Table of Contents (on this page)
Table of Contents | ||||||
---|---|---|---|---|---|---|
|
Introduction
This document outlines FCS Warning/Error Codes.
Warning Codes by Frame Type:
Code: | 5930 | Frame Type: | Full Rim | |
FCS Message: | Check HBOX consistency between sides | |||
Explanation: | Difference between Right & Left “A” size exceeds tolerance level | |||
Severity Level: | Medium | |||
Results: | Calculates, with warning on ticket | |||
Sources: | FCS settings: tolerance = 1.0 mm difference | |||
Corrective Actions: | 1) Validate as OK to use (as is) 2) Stabilize the two sides within tolerance level and trace again 3) Trace the “better” of the two sides and be aware that a size error might exist |
Code: | 5931 |
| Frame Type: | Full Rim |
FCS Message: | Check VBOX consistency between sides | |||
Explanation: | Difference between Right & Left “B” size exceeds tolerance level | |||
Severity Level: | High: If not corrected, may result in dissimilar seg heights or poor cosmetic acceptance | |||
Results: | Calculates, with warning on ticket | |||
Sources: | FCS settings: tolerance = 1.0 mm difference | |||
Corrective Actions: | 1) Validate as OK to use (as is) 2) Stabilize the two sides within tolerance level and trace again 3) Trace the “better” of the two sides and be aware that a size error might exist |
Code: | 5932 |
| Frame Type: | Full Rim |
FCS Message: | Check FCRV consistency between sides | |||
Explanation: | Difference between Right & Left frame curve (FCRV) exceeds tolerance level | |||
Severity Level: | Very High: May result in poor beveling between R/L side, if not within tolerance | |||
Results: | Calculates, with warning on ticket | |||
Sources: | FCS settings: tolerance = 1.00 diopter difference | |||
Corrective Actions: | 1) Validate as OK to use (as is) 2) Stabilize the two sides within tolerance level and trace again 3) Trace the side closest to the lens curve, and be aware of sizing problems (set large as insurance) |
Code: | 6900 |
| Frame Type: | Full Rim |
FCS Message: | Small difference between bevel and frame curve | |||
Explanation: | Curve difference is slightly higher than frame flexibility but less than 0.50 diopters | |||
Severity Level: | Low: Will likely not result in a poor bevel | |||
Results: | Calculates, with warning on ticket | |||
Sources: | FCS settings: frame flexibility = +/- 2.00 diopters, CurveGapMaximum = 3.00 diopters | |||
Corrective Actions: | 1) Review differences between applied bevel position & lens curve – if acceptable, proceed 2) Pick lenses closer to frame curve 3) Reduce/Increase frame curve closer to lens curve and trace again 4) Change beveling to another type (Layout operation) |
Code: | 5900 |
| Frame Type: | Full Rim |
FCS Message: | Excessive difference between bevel and frame curve | |||
Explanation: | Curve difference is much higher than flexibility and exceeds <CurveGapMaximum> | |||
Severity Level: | Very High: Will likely result in a non-aesthetic bevel position if not corrected or reviewed | |||
Results: | Calculates, with warning on ticket | |||
Sources: | FCS settings: frame flexibility = +/- 2.00 diopters frame, CurveGapMaximum = 3.00 diopters | |||
Corrective Actions: | 1) Review differences between applied bevel position & lens curve – if acceptable, proceed 2) Pick lenses closer to frame curve 3) Reduce/Increase frame curve closer to lens curve and trace again 4) Change beveling to another type (Layout operation) |
Code: | 5901 |
| Frame Type: | Full Rim |
FCS Message: | Check lens thickness | |||
Explanation: | Lens is thinner than tolerance | |||
Severity Level: | Low | |||
Results: | Calculates, with warning on ticket | |||
Sources: | FCS settings: minimum thickness = 1.4 mm (we grind some materials to less than a 1.4 min edge) | |||
Corrective Actions: | 1) Validate lens thickness, and if acceptable, ignore warning and proceed 2) Make lenses the correct thickness |
Code: | 5902 |
| Frame Type: | Full Rim |
FCS Message: | Selected bevel position is not a good fit | |||
Explanation: | Bevel curve specified (manual input) and FCS does not agree with our choice | |||
Severity Level: | Medium | |||
Results: | Calculates, with warning on ticket | |||
Sources: | Operator specified bevel curve inappropriate for lens curve | |||
Corrective Actions: | 1) Remove requested bevel position/curve, and process through FCS again or validate as ok 2) Common on Polaroid’s since they always bevel to lens curve regardless of frame curve 3) Run on non-FCS edger using another bevel (e.g. “automatic”) setting. |
Code: | 5903 |
| Frame Type: | Full Rim |
FCS Message: | Severe differences between frame and lens curves | |||
Explanation: | Difference between frame curve (flexed) & lens curve severe | |||
Severity Level: | Very High: Will result in a non-aesthetic bevel position if not corrected or reviewed | |||
Results: | Calculates, with warning on ticket | |||
Sources: | FCS settings: AAT function not active | |||
Corrective Actions: | 1) Change lens curve, bend frame closer, or change frame flex amount 2) Specify a different bevel position at Layout, and re-process 3) Run on non-FCS edger using another bevel setting (manual by operator) |
Code: | 5910 |
| Frame Type: | Groove & Metal Wire |
FCS Message: | Check lens thickness | |||
Explanation: | Lens too thin to groove and maintain the minimum thickness | |||
Severity Level: | High | |||
Results: | Calculates, with warning on ticket | |||
Sources: | FCS settings: tolerance = 0.5 mm to either side of groove (default width = 0.7 mm**) | |||
Corrective Actions: | 1) Validate lens thickness, and if acceptable, ignore warning and proceed 2) Make lenses the correct thickness |
** 0.7 mm wide is the default for ES-types. It is configured to lesser widths for the 6E/7E edgers
Code: | 5911 |
| Frame Type: | Groove & Metal Wire |
FCS Message: | Selected groove position is not a good fit | |||
Explanation: | Specified grooving curve will not fit in the lens | |||
Severity Level: | High | |||
Results: | Calculates, with warning on ticket | |||
Sources: | Operator specified groove curve inappropriate for lens curve | |||
Corrective Actions: | 1) Remove requested groove curve, and process through FCS again 2) Run on non-FCS edger using another groove (e.g. “standard”) setting |
Code: | 5963 |
| Frame Type: | Groove & Metal Wire |
FCS Message: | No edger capable of specified groove | |||
Explanation: | Specified Width and/or Depth exceeds limits of equipment | |||
Severity Level: | High | |||
Results: | Calculates, with warning on ticket | |||
Sources: | FCS settings file limit | |||
Corrective Actions: | 1) Validate width/depth parameters and if acceptable, proceed 2) Change width/depth manually on edger and proceed 3) Contact technical support for changes or corrections |
Code: | 5920 |
| Frame Type: | Rimless |
FCS Message: | Check lens thickness | |||
Explanation: | Lens thickness less than minimum level set | |||
Severity Level: | Medium | |||
Results: | Calculates, with warning on ticket | |||
Sources: | FCS settings: minimum thickness = 1.8 mm | |||
Corrective Actions: | 1) Validate lens thickness, and if acceptable, ignore warning and proceed 2) Make lenses the correct thickness |
Code: | 5973 |
| Frame Type: | Rimless |
FCS Message: | No defined edger capable of drilling | |||
Explanation: | Edger was expected to physically drill the lens and is not defined to perform that action | |||
Severity Level: | Low | |||
Results: | Calculates, with warning on ticket | |||
Sources: | FCS setting file limits | |||
Corrective Actions: | 1) Review FCS settings file for possible corrections (if an edger is capable) 2) Rimless is not actually calculated (adjusted) for drill work. Can typically be run on any edger in the building (FCS or not) and drilled external to edger or by use of internal database on edger |
No Calculation Codes by Frame Type:
Code: | 1906 |
| Frame Type: | All |
FCS Message: | Traced wrong side of single eye job (using a lens/pattern for shape) | |||
Explanation: | Single eye job where the tracing is for the wrong side | |||
Severity Level: | High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Tracing operator traced wrong side on a single eye job | |||
Corrective Actions: | 1) Trace same side as the RX lens to produce 2) If not possible to trace the RX side, run on non-FCS edger |
Code: | 1916 |
| Frame Type: | All |
FCS Message: | Requested edge data incomplete | |||
Explanation: | Requested bevel position (BEVP) does not contain the other data required (BEVM) | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Operator specified bevel positioning incomplete | |||
Corrective Actions: | 1) Add missing component to specified request and submit to FCS 2) Remove request and let system (FCS) decide bevel positioning |
Code: | 1907 |
| Frame Type: | Full Rim |
FCS Message: | Both sides must be traced on full rim frames | |||
Explanation: | Full rim frame must have both sides traced on a two eye job | |||
Severity Level: | High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Tracing operator did not trace both sides of a full rim frame | |||
Corrective Actions: | 1) Trace both sides 2) If not possible to trace both sides, run job on non-FCS edger |
Code: | 5950 |
| Frame Type: | Full Rim |
FCS Message: | Lens curve beyond limits of edger | |||
Explanation: | Lens curve higher than defined limits of equipment | |||
Severity Level: | High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | FCS setting file limits | |||
Corrective Actions: | 1) Review FCS settings file for possible corrections (if edger is capable) 2) Outsource to facility with appropriate equipment 3) Run on non-FCS or specialized equipment that can provide edging |
Code: | 5951 |
| Frame Type: | Full Rim |
FCS Message: | Potential block crash on edger | |||
Explanation: | B size of shape is smaller than assumed minimum edger capability – block crash warning | |||
Severity Level: | Medium | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Internal FCS setting: Minimum “B” value is defined by edger model | |||
Corrective Actions: | 1) Verify that block size smaller than minimum lens size and run on non-FCS edger 2) Likely that probe and/or block will leave a “bump” on edge requiring hand work |
Code: | 5952 |
| Frame Type: | Full Rim |
FCS Message: | No edger defined for this lens material | |||
Explanation: | Lens material is not defined in edger list | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | FCS settings file | |||
Corrective Actions: | 1) Review FCS settings file for possible corrections (if an edger is capable) 2) Outsource to facility with appropriate equipment 3) Run on non-FCS equipment that can provide edging |
Code: | 1917 |
| Frame Type: | Groove & Metal Wire |
FCS Message: | File missing groove depth or width | |||
Explanation: | Incoming file does not contain groove information for FCS calculation | |||
Severity Level: | High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Frame type is groove but no depth / width in incoming file to FCS | |||
Corrective Actions: | 1) Specify values and submit 2) Run on non-FCS edger and input/use edger values 3) LMS system error (missing default values) – call technical support |
Code: | 5960 |
| Frame Type: | Groove & Metal Wire |
FCS Message: | Lens curve beyond limits of edger | |||
Explanation: | Lens curve higher than defined limits of equipment | |||
Severity Level: | High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | FCS setting file limits | |||
Corrective Actions: | 1) Review FCS settings file for possible corrections (if an edger is capable) 2) Outsource to facility with appropriate equipment 3) Run on non-FCS equipment that can provide edging |
Code: | 5961 |
| Frame Type: | Groove & Metal Wire |
FCS Message: | Potential block crash on edger | |||
Explanation: | B size of shape is smaller than assumed minimum edger capability – block crash warning | |||
Severity Level: | Medium | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Internal FCS setting: Minimum “B” value is defined by edger model | |||
Corrective Actions: | 1) Verify that block size smaller than minimum lens size and run on non-FCS edger 2) Likely that probe and/or block will leave a “bump” on edge requiring hand work |
Code: | 5962 |
| Frame Type: | Groove & Metal Wire |
FCS Message: | No edger defined for this lens material | |||
Explanation: | Lens material is not defined in edger list | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | FCS settings file limits | |||
Corrective Actions: | 1) Review FCS settings file for possible corrections (if an edger is capable) 2) Outsource to facility with appropriate equipment 3) Run on non-FCS equipment that can provide edging |
Code: | 5970 |
| Frame Type: | Rimless |
FCS Message: | Lens curve beyond limits of edger | |||
Explanation: | Lens curve higher than defined limits of equipment | |||
Severity Level: | High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | FCS setting file limits | |||
Corrective Actions: | 1) Review FCS settings file for possible corrections (if an edger is capable) 2) Outsource to facility with appropriate equipment 3) Run on non-FCS equipment that can provide edging | |||
Code: | 5971 |
| Frame Type: | Rimless |
FCS Message: | Potential block crash on edger | |||
Explanation: | B size of shape is smaller than assumed minimum edger capability – block crash warning | |||
Severity Level: | Medium | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Internal FCS setting: Minimum “B” value is defined by edger model | |||
Corrective Actions: | 1) Verify that block size smaller than minimum lens size and run on non-FCS edger 2) Likely that probe and/or block will leave a “bump” on edge requiring hand work |
Code: | 5972 |
| Frame Type: | Rimless |
FCS Message: | No edger defined for this lens material | |||
Explanation: | Lens material is not defined in edger list | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | FCS setting file limits | |||
Corrective Actions: | 1) Review FCS settings file for possible corrections (if an edger is capable) 2) Outsource to facility with appropriate equipment 3) Run on non-FCS equipment that can provide edging |
Code: | 1911 |
| Frame Type: | Rimless |
FCS Message: | Order does not contain drill data points | |||
Explanation: | Incoming file is requesting job be drilled at edger without sending drill data | |||
Severity Level: | Medium | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Missing drill data locations in file and file is requesting FCS to provide drill info | |||
Corrective Actions: | 1) Missing drill data in source file (library) 2) Run on non-FCS edger and apply drill points 3) LMS system error – call technical support |
Info |
---|
Several codes relating to “FLAT” frame/edge types are not detailed here. Those types are used in Europe and infrequently apply to the ELOA labs. For reference, those code numbers are; 5980, 5981, and 5982. Should any of these codes appear on a work ticket, please notify FCS Support (OTG). |
General Errors:
Code: | 1900 |
| Frame Type: | All |
FCS Message: | OMA file is not valid | |||
Explanation: | FCS received an invalid DCS (oma) file | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | LMS system input file to FCS | |||
Corrective Actions: | LMS system error – call technical support |
Code: | 1902 |
| Frame Type: | All |
FCS Message: | OMA file missing trace data | |||
Explanation: | Incoming file from LMS does not contain a tracing | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | LMS system input file to FCS | |||
Corrective Actions: | LMS system error – call technical support |
Code: | 1903 |
| Frame Type: | All |
FCS Message: | Trace data in OMA file is corrupt | |||
Explanation: | Something is incorrect in the trace file sent from LMS | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | LMS system input file to FCS | |||
Corrective Actions: | LMS system error – call technical support |
Code: | 1904 |
| Frame Type: | All |
FCS Message: | OMA file has bad Z format | |||
Explanation: | Format of the Z-data is unreadable or incorrect | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | LMS system input file to FCS | |||
Corrective Actions: | LMS system error – call technical support |
Code: | 1908 |
| Frame Type: | Full Rim |
FCS Message: | OMA file missing wrap angle | |||
Explanation: | Missing calculation component required for FCS | |||
Severity Level: | High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Possible bad configuration at tracer (not sending data) | |||
Corrective Actions: | 1) Validate tracer output configuration 2) LMS system error – call technical support |
Code: | 1909 |
| Frame Type: | All |
FCS Message: | OMA file missing 3D trace data | |||
Explanation: | FCS expects either FCRV (frame curve) or Z-data (ZFMT) | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Possible bad configuration at tracer (not sending data) | |||
Corrective Actions: | 1) Validate tracer output configuration 2) LMS system error – call technical support |
Code: | 1910 |
| Frame Type: | All |
FCS Message: | OMA file missing circumference data | |||
Explanation: | Missing required component in file | |||
Severity Level: | High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Possible bad configuration at tracer (not sending data) | |||
Corrective Actions: | 1) Validate tracer output configuration 2) LMS system error – call technical support |
Code: | 1913 |
| Frame Type: | All |
FCS Message: | Traced on non-FCS tracer | |||
Explanation: | Traced on a non-FCS enabled tracer | |||
Severity Level: | High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Tracer not configured / setup for FCS calculations | |||
Corrective Actions: | 1) Trace on appropriate FCS tracer 2) Run down non-FCS edger line 3) Add tracer (if valid type) to the FCS setting file (contact technical support) |
Code: | 1914 |
| Frame Type: | All |
FCS Message: | Order does not contain frame type | |||
Explanation: | FCS did not receive the frame type (metal, plastic, rimless, etc) in the input file | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | LMS system input file to FCS | |||
Corrective Actions: | 1) Validate that frame type was included in the order. If not, then correct and try again 2) LMS system error – call technical support |
Code: | 1915 |
| Frame Type: | All |
FCS Message: | OMA file not found | |||
Explanation: | FCS can not find the associated DCS (oma) file for the tray requested | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | LMS system input file to FCS | |||
Corrective Actions: | LMS system error – call technical support |
Code: | 1918 |
| Frame Type: | All |
FCS Message: | No DBL contained in file | |||
Explanation: | Incoming file to FCS missing the DBL | |||
Severity Level: | High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Tracing device sent 00.0 for DBL or Library file on LMS contains <null> or 00.0 for DBL | |||
Corrective Actions: | 1) Correct at tracer with valid DBL (if traced) or add the DBL to the shape library 2) LMS file system error – call technical support |
Code: | 1919 |
| Frame Type: | All |
FCS Message: | File is missing either vertical HT or PD | |||
Explanation: | Incoming file is missing either the height (MF) or DPD | |||
Severity Level: | High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | Incoming file missing expected data (depending on lens type) | |||
Corrective Actions: | 1) Correct order and submit again 2) LMS file system error – call technical support |
Code: | 3900 |
| Frame Type: | All |
FCS Message: | “description of error” (data filled in by specific error) | |||
Explanation: | Communication problems between host (LMS) and RXCP (FCS) | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | LMS system input file to FCS | |||
Corrective Actions: | LMS system error – call technical support |
Code: | 3901 |
| Frame Type: | All |
FCS Message: | Impossible to initialize FCS, Check FcsSettings | |||
Explanation: | Missing data between LMS & RXCP (likely missing lens index) | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | LMS system input file to FCS | |||
Corrective Actions: | LMS system error – call technical support |
Code: | 3902 |
| Frame Type: | All |
FCS Message: | Error during reading FxML | |||
Explanation: | Communication problems between host (LMS) and RXCP (FCS) | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | LMS system input file to FCS | |||
Corrective Actions: | LMS system error – call technical support |
Code: | 3903 |
| Frame Type: | All |
FCS Message: | OpticalLib: “detailed error” (data filled in by specific error) | |||
Explanation: | Communication problems between host (LMS) and RXCP (FCS) | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | LMS system input file to FCS | |||
Corrective Actions: | 1) Check work ticket for “convex” rear curves first – FCS will not calculate double convex lenses 2) Run on non-FCS edgers 3) LMS system error – call technical support |
Code: | 3904 |
| Frame Type: | All |
FCS Message: | CalculLib: “detailed error” (data filled in by specific error) | |||
Explanation: | Communication problems between host (LMS) and RXCP (FCS) | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | LMS system input file to FCS | |||
Corrective Actions: | LMS system error – call technical support |
Code: | 3908 |
| Frame Type: | All |
FCS Message: | “OutOfBounds” (data filled in by specific error) | |||
Explanation: | Communication problems between host (LMS) and RXCP (FCS) | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | The shape is out of the lens. Can be linked to DEC, or bad lens diameter data | |||
Corrective Actions: | LMS system error – call technical support |
Code: | 3909 |
| Frame Type: | All |
FCS Message: | Can not create OMA file | |||
Explanation: | Communication problems between host (LMS) and RXCP (FCS) | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | LMS system input file to FCS (digital lens failed to calc) | |||
Corrective Actions: | LMS system error – call technical support |
Code: | 3910 |
| Frame Type: | All |
FCS Message: | Error during writing FxML | |||
Explanation: | Communication problems between host (LMS) and RXCP (FCS) | |||
Severity Level: | Very High | |||
Results: | No calculation provided, warning on ticket | |||
Sources: | LMS system input file to FCS | |||
Corrective Actions: | LMS system error – call technical support |
Simplified Codes, Numerical Order:
Code | Type | Frame Type Affected | Likely Source | Page |
1900 | ERROR | ALL | HOST SYSTEM | 7 |
1902 | ERROR | ALL | HOST SYSTEM | 7 |
1903 | ERROR | ALL | HOST SYSTEM, TRACER | 7 |
1904 | ERROR | ALL | HOST SYSTEM, TRACER | 7 |
1906 | ERROR | ALL | TRACER, HOST SYSTEM | 4 |
1907 | ERROR | FULL RIM | TRACER, DATA ENTRY | 4 |
1908 | ERROR | FULL RIM | HOST SYSTEM, TRACER | 7 |
1909 | ERROR | FULL RIM | HOST SYSTEM, TRACER | 8 |
1910 | ERROR | ALL | HOST SYSTEM, TRACER | 8 |
1911 | ERROR | RIMLESS | HOST SYSTEM | 6 |
1913 | ERROR | ALL | HOST SYSTEM, FCS SETTING | 8 |
1914 | ERROR | ALL | HOST SYSTEM, DATA ENTRY | 8 |
1915 | ERROR | ALL | HOST SYSTEM | 8 |
1916 | ERROR | ALL | DATA ENTRY, HOST SYSTEM | 4 |
1917 | ERROR | GROOVE | DATA ENTRY, HOST SYSTEM | 5 |
1918 | ERROR | ALL | HOST SYSTEM, TRACER | 9 |
1919 | ERROR | ALL | HOST SYSTEM | 9 |
3900 | ERROR | ALL | HOST SYSTEM, RXCP | 9 |
3901 | ERROR | ALL | HOST SYSTEM, RXCP | 9 |
3902 | ERROR | ALL | HOST SYSTEM, RXCP | 9 |
3903 | ERROR | ALL | HOST SYSTEM, RXCP | 10 |
3904 | ERROR | ALL | HOST SYSTEM, RXCP | 10 |
3908 | ERROR | ALL | HOST SYSTEM, RXCP | 10 |
3909 | ERROR | ALL | HOST SYSTEM, RXCP | 10 |
3910 | ERROR | ALL | RXCP | 10 |
5900 | WARNING | FULL RIM | LAB | 2 |
5901 | WARNING | FULL RIM | LAB, FCS SETTING | 2 |
5902 | WARNING | FULL RIM | DATA ENTRY, HOST SYSTEM | 2 |
5903 | WARNING | FULL RIM | LAB, FCS SETTING | 2 |
5910 | WARNING | GROOVE | LAB, FCS SETTING | 3 |
5911 | WARNING | GROOVE | DATA ENTRY, HOST SYSTEM | 3 |
5920 | WARNING | RIMLESS | LAB, FCS SETTING | 3 |
5930 | WARNING | FULL RIM | TRACER, FCS SETTING | 1 |
5931 | WARNING | FULL RIM | TRACER, FCS SETTING | 1 |
5932 | WARNING | FULL RIM | TRACER, FCS SETTING | 1 |
5950 | ERROR | FULL RIM | FCS SETTING | 4 |
5951 | ERROR | FULL RIM | FCS SETTING, LAB | 4 |
5952 | ERROR | FULL RIM | FCS SETTING | 5 |
5960 | ERROR | GROOVE | FCS SETTING | 5 |
5961 | ERROR | GROOVE | FCS SETTING, LAB | 5 |
5962 | ERROR | GROOVE | FCS SETTING | 5 |
5963 | WARNING | GROOVE | FCS SETTING | 3 |
5970 | ERROR | RIMLESS | FCS SETTING | 6 |
5971 | ERROR | RIMLESS | FCS SETTING, LAB | 6 |
5972 | ERROR | RIMLESS | FCS SETTING | 6 |
5973 | WARNING | RIMLESS | FCS SETTING | 3 |
6900 | WARNING | FULL RIM | LAB | 1 |
To view and download these instructions as a PDF file, click on the following document image.
View file name FCS - Warning-Error Codes – Version 3.1.pdf height 250